A Text-book of Assaying: For the Use of Those Connected with Mines Part 22

You’re reading novel A Text-book of Assaying: For the Use of Those Connected with Mines Part 22 online at LightNovelFree.com. Please use the follow button to get notification about the latest chapter next time when you visit LightNovelFree.com. Use F11 button to read novel in full-screen(PC only). Drop by anytime you want to read free – fast – latest novel. It’s great if you could leave a comment, share your opinion about the new chapters, new novel with others on the internet. We’ll do our best to bring you the finest, latest novel everyday. Enjoy!

dross a.s.saying 20 ozs. to the ton will contain 15 ozs. of silver. The 15 tons of lead and dross will contain 471 ozs. of silver or 31.4 ozs. per ton.

Of the methods of sampling which avoid melting the bars, that known as sawing is the only one which is thoroughly satisfactory. In it the bars are brought to a circular saw having fine teeth and are sawn across either completely or halfway through; in this way a quant.i.ty of lead sawdust is obtained (say 1 lb. or so from a bar) which represents exactly the average of the bar along the particular cross section taken and approximately that of the whole bar. A bar of lead, which by dip a.s.say gave 334 ozs. to the ton, gave on three transverse sections 333 ozs., 335 ozs. and 331 ozs. The variation may be greater than this, but with a large number of bars, where each bar is cut across in as far as possible a different place, these variations tend to neutralise each other and a good sample is obtained. Two or three cwt. of sawdust may be obtained in this way; this is thoroughly mixed and reduced by quartering in the usual way or by a mechanical sampler. A sample of 2 or 3 lbs. is sent to the a.s.sayer. This being contaminated with the oil used in lubricating the saw is freed from it by was.h.i.+ng with carbon bisulphide, ether or benzene and dried. Then, after mixing, 100 to 200 grams of it are carefully weighed and placed in a hot crucible, the heat of which should be sufficient to melt all the lead. The molten lead should not be overheated and should show no loss due to the melting. The removal of the oil may have decreased the weight by perhaps one half per cent. If the lead gives dross on heating it may be melted under 10 or 20 grams of pota.s.sium cyanide, which prevents the formation of dross.

Samples are sometimes taken with a drill, gouge or chisel, though no method of this kind is quite satisfactory. One plan adopted is to use a punch which, when driven into the bar, gives a core or rod of metal about half as long as the bar is thick and about one-eighth of an inch across. With five bars side by side it is customary to drive in the punch at one end on the first bar, and at the opposite end on the last one, and on the others in intermediate positions in such a manner that all the holes will be along a diagonal of the rectangle enclosing the bars. The bars are then turned over and similar portions punched out through the bottoms of the bars and along the other diagonal. Or one set of five may be sampled along the top and the next set along the bottom of the bars.

Silver and gold present in bars of copper are subject to the same irregularity of distribution as in lead. The sampling of such bars is guided by the same principles.[36]

CYANIDES.

The cyanides ought perhaps to be considered along with chlorides, bromides and iodides in Chapter XV. But they are treated here because they owe their importance to their use in the extraction of gold and because their determination has become a part of the ordinary work of an a.s.sayer of gold ores.

Formerly, the cyanide most easily obtained in commerce was pota.s.sium cyanide; and it was generally sold in cakes which might contain as little as 40 per cent. or as much as 95 per cent. of the pure salt. It became customary to express the quality of a sample of commercial cyanide by saying it contained so much per cent. of pota.s.sium cyanide.

The commercial product now made by improved methods of manufacture is actually sodium cyanide, but is called "pota.s.sium cyanide" (probably with the words "double salt" on the label); it contains cyanide equivalent to something over 100 per cent. of pota.s.sium cyanide in addition to a large proportion of sodium carbonate and other impurities.

What is wanted in most cases is merely a soluble cyanide, and it is a matter of indifference whether the base be sodium or pota.s.sium. But since 49 parts of sodium cyanide (NaCN = 49) are equivalent to 65 parts of pota.s.sium cyanide (KCN = 65) it is evident that a pure sample of sodium cyanide would contain cyanide equivalent to little less than 133 per cent. of pota.s.sium cyanide. Therefore a sample of cyanide reported on in this way may be rich in cyanide, and yet have much impurity.

The commonest impurity in commercial cyanide is carbonate of sodium or pota.s.sium. This may be tested for by dissolving, say, 2 grams in a little water and adding barium chloride. There may be formed a white precipitate of barium carbonate, which if filtered off, washed and treated with acid, will dissolve with effervescence. Cyanate may be tested for in the solution from which the barium carbonate has been filtered by adding a little soda and boiling; if cyanates are present they decompose, giving off ammonia (which may be tested for in the steam) and yielding a further precipitate of barium carbonate.[37] If the soda alone gave a further precipitate of barium carbonate, this may, perhaps, be due to the presence of bicarbonates. Alkaline sulphides may be present in small quant.i.ty in commercial cyanide. Their presence is shown at once when the sample is being tested for its strength in cyanide, inasmuch as the first few drops of silver nitrate solution produce at once a darkening of the liquor. A special test for sulphide may be made by adding a drop or two of solution of acetate of lead to four or five c.c. of soda solution and adding this to a clear solution of the suspected cyanide. This will cause a black precipitate or colour, if any sulphide is present.

The cyanides of the heavier metals combine with the alkaline cyanides to form double cyanides. Some of these, ferrocyanide and ferricyanide of pota.s.sium for example, have such characteristic properties that the fact that they are cyanides may be overlooked. Others, such as pota.s.sium zinc cyanide (K_{2}ZnCy_{4}), have much less distinctiveness: they behave more or less as a mixture of two cyanides and are, moreover, so easily decomposed that it may be doubted if they can exist in dilute alkaline solutions. In reporting the cyanide strength of a cyanide liquor as equivalent to so much per cent. of pota.s.sium cyanide, there is a question as to whether the cyanide present in the form of any of these double cyanides should be taken into account. It must be remembered that the object of the a.s.say is not to learn how much of the cyanide exists in the solution as actual pota.s.sium cyanide; reporting the strength in terms of this salt is a mere matter of convenience; what is really desired is to know how much of the cyanide present in the liquor is "free" or "available" for the purposes of dissolving gold. Every one is agreed as to the exclusion of such cyanides as the following: pota.s.sium ferrocyanide (K_{4}FeCy_{6}), pota.s.sium ferricyanide (K_{3}FeCy_{6}), pota.s.sium silver cyanide (KAgCy_{2}), and pota.s.sium aurocyanide (KAuCy_{2}); and the double cyanides with copper or nickel. But with cyanide liquors containing zinc the position is less satisfactory. One method of a.s.say gives a lower proportion of cyanide when this metal is present; and the loss of available cyanide thus reported depends, though in a fitful and uncertain way, upon the quant.i.ty of zinc present. The other method of a.s.say reports as full a strength in cyanide as if no zinc were present. Unfortunately, using both methods and accepting the difference in the results as a measure of the quant.i.ty of zinc present, or at any rate of the zinc present as cyanide, is not satisfactory. It appears best to use the method which ignores the zinc; and to determine the amount of zinc by a special a.s.say of the liquor for this metal.

The cyanide present as hydrogen cyanide or prussic acid (HCy) is practically useless as a gold solvent. Hence any report on the strength of a cyanide liquor which a.s.signed to this the same value as its equivalent of alkaline cyanide would be misleading. On the other hand, it is "available cyanide" inasmuch as a proper addition of sodium hydrate[38] would restore its value. The question of the presence or absence of free prussic acid is involved in the larger one as to whether the cyanide solution has the right degree of alkalinity. The a.s.say for "cyanide" should include the hydrogen cyanide with the rest.

A rough test of the power of a cyanide liquor for dissolving gold may be made by floating a gold leaf on its surface and noting the time required for its solution. This test might, perhaps, be improved by taking, say, 20 c.c. of the liquor and adding three or four gold leaves so that the gold shall always be in considerable excess. The liquor should not be diluted as this will affect the result. It should be allowed to stand for a definite time, say at least two or three hours, or better, that corresponding to the time the liquor is left in contact with the ore in actual practice. The liquor should then be filtered off and, with the was.h.i.+ngs, be evaporated in a lead dish as in the a.s.say of cyanide liquors for gold (p. 141). The gold obtained on cupelling, less any gold and silver originally present in the liquor, would be the measure of the gold dissolving power.

THE a.s.sAY FOR CYANIDE BY t.i.tRATION WITH SILVER NITRATE.

The determination of the quant.i.ty of a cyanide is made by finding how much silver nitrate is required to convert the whole of the cyanide into pota.s.sium silver cyanide[39] or one of the allied compounds. It will be seen from the equation that 170 parts by weight of silver nitrate are required for 130 parts by weight of pota.s.sium cyanide. As already explained it is customary to report the cyanide-strength in terms of pota.s.sium cyanide, even when only the sodium salt is present. One gram of pota.s.sium cyanide will require 1.3076 gram of silver nitrate. _The standard solution of silver nitrate_ is made by dissolving 13.076 grams of silver nitrate in distilled water and diluting to 1 litre; 100 c.c.

of such a solution are equivalent to 1 gram of pota.s.sium cyanide.[40]

The t.i.tration is performed in the usual way, running the standard solution of silver nitrate into a solution containing a known weight or volume of the material containing the cyanide. The _finis.h.i.+ng point_ is determined in one of two ways, both of which are largely used. In the first place, as long as there remains any free cyanide in the solution the silver nitrate will combine with it forming the double cyanide and yielding a clear solution; but as soon as all the free cyanide is used up the silver nitrate will react with the double cyanide[41] forming silver cyanide, which separates as a white precipitate and renders the solution turbid. But, in the second place, if pota.s.sium iodide is present in the solution the excess of silver nitrate will react with it,[42] rather than with the double cyanide; and silver iodide will separate as a yellowish turbidity which is easily recognised.

In working with pure solutions, the two finis.h.i.+ng points give the same results; and this is true even when there is much difference in the degree of dilution. The finis.h.i.+ng point with the iodide, however, has an advantage in precision. Moreover, it is but little affected by variations in alkalinity, which render the other finis.h.i.+ng point quite useless. The great difference between the two is shown when zinc is present in the solution. In this case, when working without the iodide, the first appearance of a turbidity is less distinct; the turbidity increases on standing and as a finis.h.i.+ng point is unsatisfactory. It can be determined with precision only by very systematic working and after some experience. The turbidity is due to the separation of an insoluble zinc compound. A most important point (to which reference has already been made) is that less silver nitrate is required to give this turbidity and, consequently, a lower strength in cyanide is reported. On the other hand, as much silver nitrate is required to give the yellow turbidity due to silver iodide as would be required if no zinc were present.

Unfortunately the difference in the two t.i.trations does not depend merely on the quant.i.ty of zinc present; as it is also influenced by the extent of dilution, the degree of alkalinity of the solution, and the quant.i.ty of cyanide present. In an experiment with .055 gram of zinc sulphate and .1 gram of pota.s.sium cyanide the difference in the two finis.h.i.+ng points was only .1 c.c.; whereas with .4 gram of pota.s.sium cyanide, the other conditions being the same, the difference was 1.5 c.c. of standard silver nitrate. On the a.s.sumption that all the zinc was present as pota.s.sium zinc cyanide (K_{2}ZnCy_{4}) the difference should have been 5 c.c. in each case. Again, repeating the experiment with .4 gram of pota.s.sium cyanide, but with .11 gram of crystallised zinc sulphate, the difference was 6.5 c.c.: that is, merely doubling the quant.i.ty of zinc increased the difference by more than four times. Hence it would appear better to use the method with the iodide and make a separate a.s.say for the zinc. But since the student may be called on to use the other method, he is advised to practice it also.

~The a.s.say without iodide.~--The standard solution of silver nitrate is placed in a small burette divided into tenths of a c.c. Ten c.c. of the cyanide solution to be a.s.sayed is transferred to a small flask and diluted with water to about 70 c.c. The silver solution is then run in from the burette (with constant shaking of the flask), a little at a time but somewhat rapidly, until a permanent turbidity appears. Since 1 c.c. of the silver nitrate solution corresponds to .01 gram of pota.s.sium cyanide, it also corresponds to .1 per cent. of this salt counted on the 10 c.c. of cyanide solution taken. The t.i.tration should be performed in a fairly good uniform light. The learner should practice on a fairly pure solution of pota.s.sium cyanide at first, and this may conveniently have a strength of about 1 per cent. For practice with solutions containing zinc make a solution containing 1.1 gram of crystallised zinc sulphate in 100 c.c. and slowly add measured quant.i.ties of from 1 to 5 c.c. of this to the 10 c.c. of cyanide liquor before diluting for the t.i.tration.

If a cyanide solution blackens on the addition of the silver nitrate it contains sulphide. In this case, shake up a considerable bulk of the liquor with a few grams of lead carbonate, allow to settle and make the a.s.say on 10 c.c. of the clear liquor.

If the cyanide liquor be suspected to contain free prussic acid, take 10 c.c. for the a.s.say as usual; but, before t.i.trating, add .1 or .2 gram of sodium carbonate. On no condition must caustic soda or ammonia be added.

The difference between the results, with and without the addition of carbonate of soda, is supposed to measure the quant.i.ty of free prussic acid. If this has to be reported it is best done as "prussic acid equivalent to ... per cent. of pota.s.sium cyanide." Suppose, for example, the difference in the two t.i.trations equals 1 c.c. of standard silver nitrate; the prussic acid found would be equivalent to .1 per cent. of pota.s.sium cyanide.

~The a.s.say with iodide.~--The standard solution of silver nitrate is placed in a burette divided into tenths of a c.c. Take 10 c.c. of the cyanide liquor, which should previously have been treated with white lead for the removal of sulphides if these happened to be present.

Transfer to a small flask, add 3 or 4 drops of a solution of pota.s.sium iodide and 2 or 3 c.c. of a solution of sodium hydrate; dilute to 60 or 70 c.c. with water. If much zinc is present the soda may be increased to 20 or 30 c.c. with advantage. The standard solution should be run in somewhat rapidly, but a little at a time, so that the precipitate at first formed shall be small and have only a momentary existence. The t.i.tration is continued until there is a permanent yellowish turbidity.

The most satisfactory and exact finish is got by ignoring any faint suspicion of a turbidity and accepting the unmistakable turbidity which the next drop of silver nitrate is sure to produce. This finis.h.i.+ng point gives results which are exactly proportional to the quant.i.ty of cyanide present; and it can be recognised with more than ordinary precision even in solutions which are not otherwise perfectly clear.

Each c.c. of the standard silver nitrate solution corresponds to .01 gram of pota.s.sium cyanide; and if 10 c.c. of the liquor are taken for a.s.say this corresponds to .1 per cent. or 2 lbs. to the short ton or 2.24 lbs. to the long ton. As already explained the result should be reported as "cyanide equivalent to so much per cent. of pota.s.sium cyanide."

The following experimental results were obtained with a solution of pota.s.sium cyanide made up to contain about 1.2 per cent. of the salt.

~Effect of varying cyanide.~--The bulk before t.i.tration was in each case 60 c.c.; 2 c.c. of soda and 3 drops of pota.s.sium iodide were used in each case.

Cyanide added 40 c.c. 30 c.c. 20 c.c. 10 c.c. 5 c.c. 1 c.c.

Silver required 47.0 c.c. 35.25 c.c. 23.5 c.c. 11.7 c.c. 5.8 c.c. 1.15 c.c.

Accepting the result for 40 c.c. as correct, the others are in very satisfactory agreement.

~Effect of varying dilution.~--The conditions were those of the 40 c.c.

experiment in the last series; but varying amounts of water were used in diluting.

Water added none 100 c.c. 200 c.c. 400 c.c.

Silver required 47.0 c.c. 47.0 c.c. 47.0 c.c. 47.05 c.c.

Very considerable dilution therefore has no effect.

~Effect of varying soda.~--The conditions were those of the 40 c.c.

experiment in the first series, except that varying amounts of soda solution were used.

Soda added none 10 c.c. 30 c.c.

Silver required 46.95 c.c. 47.0 c.c. 47.0 c.c.

This alkali therefore has no prejudicial effect.

~Effect of ammonia.~--Soda causes turbidity in some cyanide liquors; with these it should be replaced by 2 or 3 c.c. of dilute ammonia with a gram or so of ammonium chloride. The following experiments with dilute ammonia show that larger quant.i.ties of this reagent must be avoided.

Ammonia added none 10 c.c. 30 c.c. 60 c.c.

Silver required 46.95 c.c. 47.15 c.c. 47.7 c.c. 49.5 c.c.

~Effect of sodium bicarbonate.~--In this experiment 1 gram of bicarbonate of soda was used instead of the soda or ammonia of the other experiments. The silver nitrate required was only 46.45 c.c. instead of the 47.0 c.c. which is the normal result. This is probably due to the liberation of prussic acid and shows the importance of having the solution alkaline.

~Effect of zinc.~--In each experiment 40 c.c. of the cyanide solution and .5 gram of zinc sulphate crystals were used and the bulk was made up to 100 c.c. before t.i.trating.

Soda added 1 c.c. 5 c.c. 10 c.c. 25 c.c.

Silver required 47.1 c.c. 47.0 c.c. 46.9 c.c. 46.9 c.c.

The work was easier with the more alkaline solutions. The t.i.tration in the presence of zinc is comparatively easy, but, in learning it, it is well to have a burette with cyanide so that if a t.i.tration be overdone it can be brought back by the addition of 1 or 2 c.c. more cyanide and the finish repeated; a quarter of an hour's work in this way will ensure confidence in the method.

~Effect of other substances.~--It was found that an alkaline cyanate, sulphocyanate, ferrocyanide, nitrite, borate, silicate or carbonate has no effect. The ferricyanide had a small influence and, as might be expected, hyposulphite is fatal to the a.s.say. The addition of salts of lead and cadmium was without effect. On the other hand, nickel produces its full effect; and the quant.i.ty of nickel added can be calculated with accuracy from the extent of its interference with the t.i.tration.

~a.s.say of commercial cyanide of pota.s.sium.~--Break off 20 or 30 grams of the cyanide in clean fresh pieces, weigh accurately to the nearest centigram. Dissolve in water containing a little sodium hydroxide; transfer to a 2-litre flask: dilute to 2 litres; add a few grams of white lead; shake up and allow to settle. Run 50 c.c. of the clear liquor from a burette into an 8 oz. flask; add 2 or 3 c.c. of soda solution and 3 drops of pota.s.sium iodide. t.i.trate with the standard solution of silver nitrate. The percentage may be calculated by multiplying the number of c.c. used by 40 (50 c.c. is one fortieth of the 2 litres) and dividing by the weight of commercial cyanide originally taken.

~Alkalinity of commercial pota.s.sium cyanide and of cyanide solutions.~--Hydrocyanic acid like carbonic acid has no action on methyl-orange;[43] hence the alkaline cyanides may be t.i.trated with "normal acid" as easily as the carbonates or hydrates. 100 c.c. of normal acid will neutralise 6.5 grams of pure pota.s.sium cyanide.[44] A solution of commercial cyanide prepared as for the a.s.say last described, but best without the addition of white lead, may be used for the test.

Take 50 c.c. of it; tint faintly yellow with methyl-orange and t.i.trate with normal acid till the liquor acquires a permanent reddish tint. In the case of the purer samples of cyanide the quant.i.ty of acid used will correspond exactly with that required to neutralise the actual quant.i.ty of cyanide present as determined by the a.s.say with nitrate of silver.

The less pure samples will show an excess of alkalinity because of the presence of sodium carbonate or of pota.s.sium carbonate.

In comparing the alkalinity and cyanide strength of a solution the simplest plan is to take 65 c.c. of the solution and t.i.trate with normal acid; for in this case each c.c. of normal acid corresponds to .1 per cent. of pota.s.sium cyanide. In systematic a.s.says of this kind, the alkalinity would no doubt be generally in excess of that required by the cyanide present: there would be no inconvenience in recording such excess in terms of pota.s.sium cyanide.

~Determination of the acidity of an ore.~--Most ores have the power of destroying more or less of the alkalinity of a cyanide solution and in a proportionate degree of damaging its efficiency. An a.s.say is needed to determine how much lime or soda must be added for each ton of ore in order to counteract this. Whether this acidity should be reported in terms of the lime or of the soda required to neutralise it will depend on which of these reagents is to be used in the actual practice. Again, if the ore is washed with water before treating with cyanide on the large scale, then the a.s.say should be made of the acidity of the ore after a similar was.h.i.+ng.

A Text-book of Assaying: For the Use of Those Connected with Mines Part 22

You're reading novel A Text-book of Assaying: For the Use of Those Connected with Mines Part 22 online at LightNovelFree.com. You can use the follow function to bookmark your favorite novel ( Only for registered users ). If you find any errors ( broken links, can't load photos, etc.. ), Please let us know so we can fix it as soon as possible. And when you start a conversation or debate about a certain topic with other people, please do not offend them just because you don't like their opinions.


A Text-book of Assaying: For the Use of Those Connected with Mines Part 22 summary

You're reading A Text-book of Assaying: For the Use of Those Connected with Mines Part 22. This novel has been translated by Updating. Author: Cornelius Beringer and John Jacob Beringer already has 645 views.

It's great if you read and follow any novel on our website. We promise you that we'll bring you the latest, hottest novel everyday and FREE.

LightNovelFree.com is a most smartest website for reading novel online, it can automatic resize images to fit your pc screen, even on your mobile. Experience now by using your smartphone and access to LightNovelFree.com

RECENTLY UPDATED NOVEL