Make Your Own Hats Part 4

COVERING TURBANS--

Turbans are becoming to many types and are particularly suitable for the matron. Gay coverings are used on them often when they would be out of place on a larger hat. However, any material may be used; braids, alone or in combination with fabric. Velvets, georgette, satin, and taffeta are used. A turban covered entirely with flowers sewed down flat makes a charming hat: the lower edge invariably looks better if first bound with a bias piece of velvet no matter what the covering may be--it seems to give a softer look around the face. A round crown of buckram makes a good turban frame if a bias strip of crinoline an inch wide is sewed to the lower edge to give a little flare. A frame of this kind may be draped with velvet, satin, georgette, or any pliable material, and when skillfully done the effect is beautiful indeed.

CHAPTER IV

WIRE FRAMES

EQUIPMENT

Brace wire or frame wire Tie wire Sprung wire Pliers

TO OPEN COIL OF WIRE--

Hold the coil in the left hand; unfasten and allow it to loosen gradually in the hand; pa.s.s it over the arm and knock it until the coils separate.

TO CUT WIRE--

Place wire firmly and squarely between the jaws of the pliers at the point where they cut and press straight down. Be sure to cut with the first attempt; otherwise, if the wire is haggled off, the pliers are injured and the covering loosened at the ends of the wire which will make it impossible to tie them together.

TO STRAIGHTEN WIRE--

Pa.s.s the wire between the thumb and finger with a sweeping motion. A piece of cloth or paper may be held in the hand if the fingers become tender. Do not make small dents in the wire in attempting to straighten it, as it will be impossible to remove them.

TO TIE WIRE--

Ends of brace wire parallel.

Right angles tied diagonally.

Brace wire tied without use of tie wire.

Before beginning to make a frame of wire, time will be saved and necessary experience gained by tying a few short pieces of wire, until a strong joint can be made. Cut fifty pieces or more of tie wire three-quarters of an inch long. Cut two pieces of brace or frame wire two or three inches long. Lap the ends of the heavy wire one inch, then lap one of these pieces of tie wire around once as close to the end of the brace wire as is possible. Hold in the left hand and with the end of the pliers grasp the ends of the tie wire as close to the brace wire as possible and twist tightly until the joint feels firm. Place pliers back a little and twist several times until a little cable is formed. Cut this off, leaving an eighth-inch end. Press this end down flat with the jaws of the pliers. Tie the other end in the same manner. Practice this until a satisfactory joint can be made with ease, before attempting to make a frame of wire.

[Ill.u.s.tration: TO TIE TWO WIRES WITH TIE WIRE]

[Ill.u.s.tration: TO TIE TWO WIRES DIAGONALLY WITH USE OF TIE WIRE]

[Ill.u.s.tration: METHOD OF MAKING PAPER PATTERN FOR DROOPING BRIM]

[Ill.u.s.tration: METHOD OF PINNING FABRIC ON DROOPING BRIM]

[Ill.u.s.tration: BRAID-COVERED BRIM SHOWING METHOD OF FILLING IN SHORT LENGTHS WHEN THE DIFFERENCE IN WIDTH OF THE TWO SIDES IS VERY GREAT]

[Ill.u.s.tration: PATTERN PINNED IN PLEATS FOR SHAPED BRIMS OF FABRIC.

ILl.u.s.tRATION SHOWS PATTERN PINNED ON BUCKRAM READY TO CUT]

TO FASTEN TWO PIECES OF BRACE WIRE DIAGONALLY--

TO FASTEN TWO PIECES OF BRACE WIRE WITHOUT THE USE OF TIE WIRE--

Hold the strand of wire against the wire to which it is to be fastened, at right angles to it, with about two and one-half or three inches extending beyond the point at which the twist is to be made. Press the end straight backward, close to and parallel with the other end of the wire. The end should pa.s.s once and a half around. Use the jaws of the pliers to press parallel wires in the twist together, and to tighten the twist. Cut the end off close and use the pliers to press the end down flat.

TO MAKE WIRE FRAME FOR HAT HAVING FLAT BRIM AND SQUARE CROWN--

Always remember that it will greatly simplify the work first to make a paper pattern for every hat. A hat is seldom made with all sections of the brim of equal width, and this is one important reason why it is more satisfactory first to make a paper pattern.

PATTERN FOR BRIM--

Make a pattern the same as for a straight-brim sailor, being careful to fold the pattern in halves from front to back, and to crease sharply.

Fold the halves into fourths and the fourths into eighths and crease.

This is to determine the position of the wire spokes in the brim. The eight creases will correspond to the eight spokes in the brim; this is the correct number of spokes.

HEADSIZE WIRE FOR WIRE FRAME--

A wire frame needs two headsize wires, so cut two just alike, remembering always that the headsize wire is the most important wire in any hat, as the comfort of the wearer depends upon the measurements taken for this wire. Measure as for the headsize in a fabric hat, lapping the ends one inch, and tying them. Try on these wires and shape to fit the head. They should usually be elongated two inches.

Pin the headsize wire on the paper pattern, placing the joining on the back crease and the exact center front of wire on the front crease; next pin the sides securely, being careful to keep the wire shaped to fit the head. Allow one-half inch inside of wire and slash every half inch out to headsize wire. The pattern may now be tried on the head for any necessary alterations. The brim pattern may be added to or cut away.

WORKING MEASUREMENTS NEEDED--

Make a pencil mark on the pattern around the headsize wire. Before removing the wire, mark the eight different points where it crosses the creases in the paper pattern. Remove the wire from the pattern.

STICKS FOR BRIM--

Straighten and cut four pieces of frame wire the length of the diameter of the brim plus three inches for finis.h.i.+ng. Place one of these sticks across the headsize wire from front to back on the marks made by the pencil, allowing the ends to extend an equal length. Fasten to the headsize wire with tie wire. Place the next stick from side to side, joining on the pencil marks. The two remaining sticks when placed on the remaining marks divide the circle into eighths. This is called the skeleton of the brim; the wires are named _front_, _back_, _right side_, _left side_, _right side front_, _right side back_, _left side front_, _left side back_. The position of these ends or spokes should correspond to the creases in the paper pattern, and the length of each one should be determined by measuring the corresponding crease on the pattern.

EDGE WIRE--

Cut a circle of brace wire the exact length of the circ.u.mference of the brim plus one inch for lap and tie. Lay this close to the edge of the pattern and mark on it with pencil where each crease touches it, always keeping the tied ends on the back crease. If these measurements are carefully made, the brim will be exactly like the pattern.

TO JOIN EDGE WIRE--