Mission Furniture Volume II Part 9

This cedar chest for storing unused bedding or furs is not a difficult thing to make and when made, the hard oak binding takes the wear and protects the softer cedar so that the chest ought to serve several generations. Order the stock as follows:

CEDAR

2 top and bottom pieces, 7/8 by 16-1/2 by 34-1/2 in., S-2-S.

2 sides, 7/8 by 18-7/8 by 34-1/2 in., S-2-S.

2 ends, 7/8 by 18-7/8 by 14-3/4 in., S-2-S.

OAK

2 overhanging top pieces, 1 by 1 by 36-1/2 in., S-4-S.

2 overhanging top pieces, 1 by 1 by 18-1/2 in., S-4-S.

2 lock and hinge rails, 1 by 2-1/2 by 36-1/2 in., S-2-S.

2 lock and hinge rails, 1 by 2-1/2 by 18-1/2 in., S-2-S.

2 base pieces, 1 by 3-1/4 by 36-1/2 in., S-2-S.

2 base pieces, 1 by 3-1/4 by 18-1/2 in., S-2-S.

[Ill.u.s.tration: Details of Cedar Chest]

Specify thoroughly seasoned Tennessee red cedar and plain sawed white oak and have the different pieces mill-planed and sandpapered as indicated in the stock-bill. This bill allows 1/2 in. extra on the length and the width of each piece for "squaring up" of all pieces except those marked to be surfaced on four sides.

Begin by squaring the sides and ends to size. Probably the best joint for the corners is the dovetail. If the worker is not experienced in woodworking, some of the more simple joints will do. It will be noted that the drawing and stock-bill call for the simplest form of joint, that in which the sides of the chest lap over the end. For the dovetail joint it will be necessary to add 2 in. more to the length of the end pieces, making them 16-3/4 in. each in the rough.

Having got the sides and ends ready, fasten them together. The perspective shows the sides fastened to the ends with ornamental headed nails. Common nails are first used, being equally s.p.a.ced, and the ornamental heads are afterwards placed so as to cover their heads.

Next square the bottom and nail it to the parts just a.s.sembled. Square the top to the same size.

The base stuff is squared on one edge only. The second edge--the upper one--is to be beveled or sloped 1/8 in. to facilitate dusting and for appearance sake. Fit these base pieces to place, mitering the joints.

Before fastening the parts to the chest proper, gauge a line 3/4 in.

from the lower edge and to a point 4-1/2 in. from each end, cut out to this line and shape the base as shown in the drawing. Use finis.h.i.+ng nails for fastening the base to the chest. The heads should be "set" so they may be covered later with a putty colored to match the finish.

In a similar manner plane up, cut and fit the back and hinge rails.

These rails should be kept a "scant" 1/8 in. below the top edges of the chest proper. The overhang of the lid fits down over in such a way as to form a dust-proof joint between lid and chest proper.

The overhang of the lid of 1 in. by 1-in. stock may next be mitered, fitted and nailed to the lid. Thoroughly sandpaper all parts not so treated and finish as follows: Put on all the oak pieces, two coats of natural paste filler. This is best done before they are fastened in place. Directions will be found on the cans in which the filler is kept.

The red of the cedar may be heightened by applying a mahogany stain made of Bismark brown aniline and boiling water, in the proportion of 3 qt.

of water to 1 oz. of aniline. If applied hot the stain will enter the wood better. When dry, sandpaper lightly with No. 00 paper, both this and the oak-filled pieces.

Fasten the oak pieces in place and give the whole exterior a very thin coat of sh.e.l.lac. After this has hardened, apply two coats of wax. Wax comes in paste form and is to be applied with a cloth very sparingly.

Allow it to stand five or ten minutes then rub briskly with a soft dry cloth to polish. The first coat is allowed to stand 24 hours before the second is applied in a similar manner.

Another finish, known as an egg-sh.e.l.l gloss sh.e.l.lac finish, is obtained by omitting the wax and instead applying from two to five more coats of sh.e.l.lac. Allow each coat 24 hours in which to harden, and rub each hardened coat to a smooth finish, using curled hair, or fine steel wool, or fine oiled sandpaper, before applying the next.

[Ill.u.s.tration: Cedar Chest Complete]

The metal reinforcements for the corners can be bought at a hardware store, as can the lock, hinges, and handles. These parts are applied in the usual manner--b.u.t.t hinges being used.

If well made, the chest is practically airtight. The interior is all of red cedar, while the effect of the exterior in combining the light oak and the red cedar is striking.

A TOOL FOR MAKING MORTISES

In the construction of mission furniture where mortise joints are mostly used, those who cannot have access to a mortising machine will find the following method of great a.s.sistance in obtaining a true mortise, which is necessary in work of this kind.

[Ill.u.s.tration: Boring Holes for Tenons]

Take a block of wood, A, the exact thickness of the piece B to be mortised, and with an auger bore a hole, the same size as the width of the mortise to be made, exactly parallel to the sides of the block. This can best be done on a drill press or a wood boring machine. If no machine is available, great care should be taken in boring by hand, to get the hole as nearly true as possible. Then nail a cleat, C, on the side of the block, A, and let it extend down on piece B. Use a clamp to hold the block in place while boring out the mortise. By changing the position of the block and boring a number of holes, any length of mortise can be made. The holes should afterwards be squared up with a chisel.

A DRESSER FOR CHILD'S PLAYROOM

This dresser can be made of two kinds of wood as marked on the drawing or it can be made all of one kind. The original dresser was made of oak and walnut and was finished natural, the contrast between the light and dark woods adding much to the value of the piece in the eyes of the little ones. Have all surfaces that will show well sandpapered at the mill. The following is a list of the material wanted:

4 oak posts, 1-1/2 in. square by 19-1/2 in., S-4-S.

3 walnut drawer fronts, 3/4 by 5 by 17 in., S-2-S.

6 yellow poplar drawer sides, 3/8 by 5 by 12 in., S-2-S.

3 yellow poplar backs, 3/8 by 4-1/2 by 16-1/2 in., S-2-S.

3 yellow poplar bottoms, 3/8 by 12 by 16-1/2 in., S-2-S.

4 oak front stretchers, 7/8 by 1-3/4 by 17-1/2 in., S-4-S.

4 oak side rails, 7/8 by 2 by 12 in., S-4-S.

2 walnut side panels, 1/4 by 11 by 14-1/2 in., S-2-S.

8 oak drawer slides, 7/8 by 2 by 10-1/2 in., S-2-S.

6 oak drawer guides, 1/2 by 3/4 by 10-1/2 in., S-2-S.

4 oak back stretchers, 7/8 by 2 by 17-1/2 in., S-2-S.

1 oak top, 5/8 by 14 by 20-1/2 in., S-2-S.

3 sq. ft. of 3/8 in. matched yellow pine ceiling for back.

MIRROR SUPPORT

1 walnut piece, 7/8 by 1-3/4 by 20-1/2 in., S-2-S.

1 walnut piece, 7/8 by 1-1/2 by 18 in., S-2-S.

1 oak piece, 3/4 by 1-1/4 by 10-1/2 in., S-2-S.

2 oak pieces, 7/8 by 1-1/2 by 11 in., S-2-S.

1 walnut bracket piece, 7/8 by 1-1/4 by 5 in., S-2-S.

MIRROR FRAME PARTS

2 walnut pieces, 7/8 by 1-1/2 by 12-1/2 in., S-2-S.

2 walnut pieces, 7/8 by 1-1/2 by 10-1/2 in., S-2-S.

2 oak pieces, 1/4 by 3/8 by 10 in., S-4-S.

2 oak pieces, 1/4 by 3/8 by 8 in., S-4-S.