The Boy Mechanic Part 107

** Home-Made Roller Skates [386]

The rubber-tired wheels of an old carpet sweeper can be used to advantage in making a pair of roller skates. In Fig. 1 is shown how an iron washer or two may be fastened to the wood with a piece of sheet metal to support

[Ill.u.s.tration: Rubber Tired Roller Skate]

the short axles of the wheels. The wheels are oiled through the holes A and B, Fig. 2. These holes should be smaller than the axles. The two side pieces are fastened together with a board nailed on the top edges, as shown. This board also furnishes the flat top for the shoe sole. Two straps are attached for fastening the skate to the shoe.

--Contributed by Thos. De Loof, Grand Rapids, Mich.

** Adjuster for Flexible Electric Wires [386]

The accompanying ill.u.s.tration shows an adjuster for changing the drop of an electric light. The main feature of this adjuster is that it can be removed from the cord at any time. The adjuster is made from a piece of wood, 3/8 in. thick, 2 in. wide and 3 in.

long. A 1/4 in. hole is bored in the center near each end of the wood and a slot cut from

[Ill.u.s.tration: Can Be Taken from the Cord]

the holes to the outside edge, as shown in Fig. 1. It is attached to the flexible cord as shown in Fig. 2.

--Contributed by J.J. Voelcker; Decatur, Ill.

** Making Photographs on Watch Dials [386]

Beat to a foam the white of an egg, with the addition of a little ammonia. Add 9 oz. and 3 dr. of water and beat again. After the egg has settled, filter and let the liquid run over the dial, which has been previously cleaned with ammonia. When the surplus has run off, coat with the mixture and allow to dry.

A sensitive collodion is now produced as follows: Dissolve 9 gr.

of chloride of zinc in 5 dr. of alcohol; add 7-1/2 gr. of collodion cotton and 6-1/2 dr. of ether. Shake the whole forcibly.

Dissolve 23 gr. of nitrate of silver in hot water, add 1-1/2 dr.

of alcohol and keep the whole solution by heating. The silver solution is now added in small quant.i.ties at a time to the collodion, which must be well settled. This, of course, is done in the dark room. After 24 hours the emulsion is filtered by pa.s.sing it through cotton moistened with alcohol. This durable collodion emulsion is now flowed thinly upon the prepared watch dial, which, after the collodion has coagulated, is moved up and down in distilled

water until the fatty stripes disappear. The water is then changed once, and after a short immersion, the dial is left to dry on a piece of blotting paper. It is now ready for exposure.

Expose under magnesium light and develop with a citrate oxalic developer, or in the following hydroquinone developer:

Hydroquinone .............1 dr.

Bromide of pota.s.sium .... 6 dr.

Sulphite of soda......1-1/2 oz.

Carbonate of soda ....2-2/3 dr.

Water....................14 oz.

After fixing and drying, coat with a transparent positive varnish.

** Home-Made Overhead Trolley Coaster [387]

The accompanying sketch shows a playground trolley line which furnished a great deal of amus.e.m.e.nt to many children at a minimum cost. The wire, which is 3/16 in. in diameter, was stretched between a tree and a barn across a vacant quarter block. The strength of the wire was first tested by a heavy man. When not in use the wire is unhooked from the tree and

[Ill.u.s.tration: Details of the Trolley and How It Is Used]

hauled into the barn and coiled loosely in the hay loft. The wire was made taut for use by a rope which was fastened to the beams in the barn. The trolley was made, as shown in Figs. 1 and 2, of strips of wood bolted with stove bolts on two grooved pulleys. The middle wide board was made of hardwood. The wheels were taken from light pulley blocks and stove bolts were purchased from a local hardware store to accurately fit the hubs. As it was necessary to keep the bearings greased, we used vaseline. This coaster made great sport for the youngsters and at no time were they in danger of a serious fall as the line was hung low and the slant of the wire was moderate.

--Contributed by H. J. Holden, Palm Springs, Calif.

** How to Make an Electric Furnace Regulator [388]

We have a furnace in our house and a part of my work each evening last winter was to go down in the bas.e.m.e.nt at 9 o'clock, fill the furnace with coal for the night and stay there until it was burning in good shape, then to close the draft door. As this performance requires from twenty to thirty

[Ill.u.s.tration: Details of Furnace Regulator Construction]

minutes I concluded to make a self-acting device which would close the draft and leave the furnace safe, without any further attention on my part, after putting in the coal and opening it up to burn. As some other boys may like to build the same regulator I will tell just how to make one and how it operates.

Referring to Fig. 1, you will see a straight cord is attached to the draft door of the furnace, D, and is run over the pulley P and finally is attached to a small piece of iron H. This piece of iron is hinged to 1. To the other side of H another cord G is fastened, which pa.s.ses over the pulley N and terminates in any convenient place in the rooms above. This piece of iron H is held in place by the release A. Now C is a coil of wire from a door bell. R is an armature which works A on pivot J. M is a U-tube, filled with mercury, one end being connected to a half liter gla.s.s flask F by the tube T, and the other end terminates in an overflow tube O. B is a battery of three b.i.+.c.hromate cells which are connected up with the C and the platinum points 1--2, which are fused into the U-tube.

On fixing the furnace the iron piece H takes position X, this being the normal position when draft door D is closed. On arriving upstairs I pull the cord G, which causes the piece H to become fixed in the vertical position by means of A. This opens the draft door at the same time. Now when the furnace heats up sufficiently it causes the air to expand in F, which causes the mercury in M to rise a little above the point 2. This immediately causes a current to flow through C which in turn draws R towards it, raises A and causes H to drop to position X. This shuts the furnace door. Now the furnace, of course, cools down, thus causing the air in F to contract and consequently opening the circuit through C. If at any time the furnace should overheat, the raising of A, on which is grounded a wire from a signal bell upstairs, will make a circuit through the bell by means of the point Z and wire leading therefrom. This bell also serves to tell me whether H has dropped or not. This same device of regulating the draft D can be used to regulate the damper, found on the coal doors of most furnaces, by simply fusing a platinum point on the other side of M and changing the cord which is attached to D. A two-contact switch could also be inserted to throw connections from 2 to 3. It would work in this manner: The damper door, of course, which keeps a low fire, would be up in a position similar to D; on the furnace cooling too much, connection, due to contracting of air in F, would be made through 3 and C, causing H to drop, thus closing door. This simple device worked very well all last winter and gave me no trouble whatever.

If you cannot readily procure a U-tube, you can make one, as I did, and the work is interesting.

The U-tube is constructed in the following manner. A gla.s.s tube is closed at one end. This is done by holding the tube in one corner of a gas flame, somewhat near the dark area (A, Fig. 2), and constantly turning the tube, when it will be found that the gla.s.s has melted together. Now, after it is cool, about 3 or 4 in. from the sealed end, the tube is held steadily so that the flame will heat one small portion ( B, Fig. 2 ). After this small portion is heated blow into the tube, not very hard, but just enough to cause tube to bulge out. Allow to cool. Then reheat the small bulged portion, blow quite hard, so that the gla.s.s will be blown out at this point, forming a small hole. Now insert about 1/2 in. of platinum wire and reheat, holding platinum

[Ill.u.s.tration: Making the U-Tube]

wire by means of a small pliers so that it will be partly in the tube and partly without. The platinum will stick to the gla.s.s, and if gla.s.s is sufficiently heated one will be able to pull it, by means of pliers, from one side of the hole to the other, thus sealing the wire into the tube. Another wire is sealed in the same way about 1 in. from the first. Now, to bend the tube, one must hold it, with both hands, in the flame and turn constantly until soft. Quickly withdraw from flame and bend, just as you would a piece of copper wire. Allow to cool slowly.

The several tubes are connected with a short piece of rubber tubing.

The total cost of materials for constructing the apparatus complete will not amount to more than one dollar.

--Contributed by M. G. Kopf, Lewis Inst.i.tute, Chicago.

** Weatherproofing for Tents [389]

Dissolve 4 oz. sulphate of zinc in 10 gal. water; add 1/2 lb.

sal-soda; stir well until dissolved, and add 1/2 oz. tartaric acid. Put the tent cover in this solution and let lie 24 hrs. Take out (do not wring it) and hang up to dry. Grinnell's Hand Book on Painting.

** Sawing Sheet Metal [389]

Sheet metal placed between two boards in the jaws of a vise and clamped tightly, can be sawed easily with a hacksaw.